Page 13 of 13
600W Original Type Charging System Upgrade Bosch Equipped Models ELA00503 Fits Cali 2, T3, 750S, S3, 850T, T4, T5 (Series 1), Convert, G5, 1000 SP, SP II, Le Mans 1, Le Mans 2, Le Mans 3, Le Mans 1000, Mille GT (Series 1), V35, V35C, V35 Florida, Imola 2, V35 TT, V50, Monza, V65, V7 Sport Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders. - Outputs 600W @5000 RPM
- Supplied with rotor removal tool
- For tapered crankshafts
Banish charging system worries with this kit!
Installation notes: - Remove stator and rotor using the supplied rotor removal tool
- Remove the old stator windings from the stator plate
- Solder in the new stator widing wires to the connection block on the stator plate and reconnect the
- Mount the replacement diode board, this should be protected from the weather but cooled by passing air
- Connect up the system as follows: Terminals U,V and W take the three yellow wires which should be connected to the stator plate block; Y goes to Y on the stator plate; The brown wires go to earth (we recommend using some earth sleeve on these if possible); Red goes to the battery positive terminal; regulator wiring remains as before (D+ to diode board, D- to earth and DF to brush holder)
- Check charge warning light is working (earth DF wire at stator to check bulb function)
- Turn motor over by hand to ensure everything is seated correctly, there should be an air gap between the stator windings amd rotor
Fit alternator cover and spacer This part is available by special order, request a quote £465.00 INC VAT £387.50 EX VAT Banjo Brake Light Switch Fine Thread ELA14959 Fits 1100 Sport ALL, Centauro, Daytona (1991-1996), V11 Sport, V35 I, V35 II, V35 3, V35 Florida, V35C, V50 I, V50 II, V50C, V50 3, Monza, V65, V65 Florida, V65 GT, Lario, Quota ALL, Le Mans 1, Le Mans 2, Le Mans 3, 1000 SP, SP II, Spada 3, S3, T3, T4, T5, Cali EV, Cali Jackal, Cali Stone, Cali 3, Cali 1100 (1994-1997), Strada 1000, Nevada 750 (1991-2003) Dimensions: M10 x 1 x 17mm bolt, 18mm from end to underside of bolt head Brakelight switch banjo bolt See BRA01004 and BRA01014 for alternative universal stop light switch. Also known as Guzzi ref. 06261020, 000037891, 800037891, 079654114, 14657050 This part is due back in stock soon, call 01484 841395 to reserve yours 14657959 GU14657959 14 65 79 59 1465 7959 1465.7959 14.65.79.59 £21.00 INC VAT £17.50 EX VAT Page 13 of 13
|